TurboGrafx Turbo Express gets no power

[dendawg]

No offense but if you need a walk through it is too advanced for you.

I thought the point of this board was to help less "advanced" people, and not snark at them?

[BlueBMW]

I learned to work on stuff by asking lots and lots and lots of questions and then making lots and lots of mistakes I'm still not that good at any of this stuff, but over time I keep getting better and better. Being willing to try is admirable in and of itself. Some people are too afraid to even attempt to repair their stuff.

[c0ldb33r]

ha true but maybe start with something less valuable than a turboexpress

[APE992]

I thought the point of this board was to help less "advanced" people, and not snark at them?

That was not snark. This is EXTREMELY basic soldering: apply desoldering braid, remove solder, remove part, place in new part, solder, done.

The truth isn't always candy coated with a shiny, pretty bow on it. Not everyone should attempt something just because it is possible: reality hurts.

[dendawg]

That was not snark. This is EXTREMELY basic soldering: apply desoldering braid, remove solder, remove part, place in new part, solder, done.

The truth isn't always candy coated with a shiny, pretty bow on it. Not everyone should attempt something just because it is possible: reality hurts.

...And who, exactly, are you to determine whether someone should attempt something like soldering or not? So in your world, somebody who doesn't know how to do something shouldn't attempt to do so, even after asking to be shown how? Again, this is a board to help people do so, and your little comment did nothing to contribute, aside from being a negative asshole about it. If you're not going to contribute something educational, then by all means, STFU.

[APE992]

...And who, exactly, are you to determine whether someone should attempt something like soldering or not? So in your world, somebody who doesn't know how to do something shouldn't attempt to do so, even after asking to be shown how? Again, this is a board to help people do so, and your little comment did nothing to contribute, aside from being a negative asshole about it. If you're not going to contribute something educational, then by all means, STFU.

I offer advice, not judgements but it sure sounds like you're offering judgements. My advice does not have to be taken as gospel and can be disregarded though that can be a bad idea at times. How about contributing a useful guide yourself or are you just going to offer negativity? I can see I sure hit a soft spot in someone's ego though.

As I already stated, you desolder the old part, insert the new part and solder it in. Simple and easy but easy and simple to screw up as I have done so in the past. I have also cleaned up the mistakes of others who have attempted mods they were not yet prepared for. Though in this case I don't see why OP couldn't handle it himself I just wanted to be sure that he had any doubts he would listen to them. I've got the scars to prove that doing that might save you a 2nd degree burn from a heatgun.

PS: I'm working on a BS in Electrical Engineering and have over a decade of experience with soldering and electronics repair. I didn't realize I should have my resume pinned to my lapel.

[theclaw]

You need to start small. There's a gray area beyond which jobs are no longer reasonable. We're talking soldering not the infinite monkey theory. Dumb luck only goes so far. Past that difficulty level one isn't ready to handle, probability is greater you'll irreversibly hurt yourself and/or the object in question, over achieving results positive enough to justify said risk.

[dendawg]

I offer advice, not judgements but it sure sounds like you're offering judgements. My advice does not have to be taken as gospel and can be disregarded though that can be a bad idea at times. How about contributing a useful guide yourself or are you just going to offer negativity? I can see I sure hit a soft spot in someone's ego though.

So how's the weather up there from your high horse? You offered only one sentence of advice, then tore into the OP fourposts later.....and I hit somebody's sore spot? Pot meet kettle. Needless to say, I won't be posting a guide as your intelligence/methodology weren't being attacked, rather your condescending attitude.

As far as the rest of your post goes, bravo, you're going for a degree. Too bad you're taking the Dr. House route in "bedside manner," so to speak, instead of that of say, Einstein.

I'm done derailing this thread and will offer no more public replies.

[APE992]

I'm done derailing this thread

Which is all you've done thus far.

To OP: if you'd like help figuring out where the regulator is I can help but I don't have any images on hand of the Turbo Express PCB.

[turboexpress]

I'm having the same problem with my TE. Any updates on this?