RGB to Component Video (YPbPr) Chip Now For Sale!!!!-For Turbografx/PCE/Genesis/SNES

[turbokon]

Hey guys, turbokon here, I don't get on here much but I do stay active over at pcenginefx.com forum. I have been working on a rgb to component converter and just released it for sale.

Finally a rgb to component video converter based on original design by pcenginefx's thesteve. Originally designed for all NEC turbografx and pc-engine systems, with three resistors, now works for all rgb enabled systems.

Now works with the all rgb enabled systems with the addition of three resistors to rgb signals from system to rgb input on component video board. Resistor values depend on voltage of RGB signals coming in from system. Works with a genesis using 1K ohm resistors at RGB signals. More systems will be tested to determine the right resistors value.

$32 shipped within US.

Go to this website for ordering and payment processing:

www.tg16pcemods.com

This component video chip will only work on HDTV sets that accept 240P. *Check to make sure your HDTV supports 240P before ordering.

I throw together a quick installation guide here:

http://www.mediafire.com/?x7m3oxarr9p74x0

Video:
http://youtu.be/EeqmgNaq0-k

Some pictures:




Component Video installed in a Turbo Duo





Installed in a turbografx-cd dock





Installed in a pc-engine








Installed in TE


Video of Street Fighter II in component video:
http://youtu.be/_CyxG7sBsdY

Installed in a genni.


More pictures of the component video board in action




SNES
IMG]http://i1125.photobucket.com/albums/l594/superkon316/pc-enginefx/null-92.jpg[/IMG]

[turbokon]

Added a video link if street fighter in action on component video.

[c0ldb33r]

Can you switch between composite and component after the mod?

[turbokon]

Yep, it still keeps the composite signal.

[RGB_Gamer]

Would I be able to do SCART RGB out with this? I have an RGB. (15Khz/31khz) monitor. Also, Do you happen to have an installation guide? I have a core grafx2/cdrom2

[c0ldb33r]

Will it fit easily on a Coregrafx 2

[turbokon]

I believe you can if your monitor accept component video. I do have the install guide, it's the mediashare link on top.

[turbokon]

Will it fit easily on a Coregrafx 2

Yes it can. I built it so that it can even fit in a TE or GT. See the updated pictures above where I installed it in a pc-engine and TE.

[Greg2600]

Would I be able to do SCART RGB out with this? I have an RGB. (15Khz/31khz) monitor. Also, Do you happen to have an installation guide? I have a core grafx2/cdrom2

I've seen implementations where the RF port is replaced with an 8-pin that fits the Sega Genesis SCART cable for example.

[RGB_Gamer]

I wouldnt mind if my cdrom2 had a SNES style connector

[turbokon]

I've seen implementations where the RF port is replaced with an 8-pin that fits the Sega Genesis SCART cable for example.

I have done the same thing to several pce and tg16 where I installed a mini din 7 connecter and used a mini din 7 to component cable. I have also used a din 8 for a couple duo's to keep the stock look and made a custom cable for it.

[turbokon]

Now works for all rgb enabled systems with additional three resistors.

[c0ldb33r]

If I pay extra can you include the required wiring and resistors?

[turbokon]

Sure, I can do that.

[turbokon]

Just installed this component board in a genni

[c0ldb33r]

I'd like this in my pce duo. Could I pay to have you install it and replace all the caps?

[Kitsune Sniper]

God DAMN that looks nice.

[turbokon]

I'd like this in my pce duo. Could I pay to have you install it and replace all the caps?

Sure you bet. Check out my website for more details.

www.tg16pcemods.com

[turbokon]

Confirmed that the component boards work with the SNES. More systems testing to come.

[turbokon]

More pictures of the component video board in action

Genesis




SNES