Results 1 to 5 of 5

Thread: Help with RGB Mod (Based on 8-Bit Guys video)

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Kirby (Level 13) megasdkirby's Avatar
    Join Date
    Oct 2003
    Location
    Bayamon, Puerto Rico
    Posts
    5,255
    Thanks Thanks Given 
    13
    Thanks Thanks Received 
    10
    Thanked in
    9 Posts
    Xbox LIVE
    megasdkirby
    PSN
    megasdkirby

    Default Help with RGB Mod (Based on 8-Bit Guys video)

    Long shot post, but who knows...some text was meant for another forum...Im just lazy as hell.

    Hello everyone!

    I've been checking out the forums, particularly the RGB mod section, as I have many CRTs I would like to mod. The first unit to test out was a Curtis Mathes 19" CRT, model CM19011BX. I found the jungle chip and it's a TN1282N. The chassis is a K15A AA41-11037C. The OSD chip is SZM-370TH1. Looking at the schematic, it's almost identical to the CRT modded by the 8-bit guy on his Youtube video a few years ago, with the only differences been the size of the unit (his was a 13" while this one is 19"), the model of the MICOM and Jungle Chip, and finally some capacitors and diodes here and there. While this may seem like everything is different, the reality is that, by looking at the schematic, it was eerily similar, so I decided to start with this one, as I have a reference to go by.

    Using the methods in both videos, I did manage to RGB the unit and it looks BEAUTIFUL! Crisp, detailed image...so gorgeous. MarkOZLAD helped me quite a bit to understand some of the reasons behind certain steps, so an awesome THANK YOU for the help!

    However, there are issues. The least important one being that after the mod, the screen in RGB mode looked too bright. MarkOZLAD recommended that I lower the brightness on the flyback, which I did, and now it looks fantastic. Problem solved for that issue. The main issue that still haunts me is an OSD issue. For some reason, even when the 5V and all the wires are correct and the switch is configured correctly (as in 8-bit guy's second video), the unit will keep displaying the "VIDEO" and "PLEASE INSERT AV CONNECTION" on the screen. It happens in RGB mode, non RGB mode, and even while playing a game. Even the remote display button doesn't help. So something is a miss. I rechecked all connections and everything is in order. Made sure I used the correct sections for voltage and ground, as well as jump the resistor for the CCD, and that is ok as well. As a last resort, I disconnected the three pins 22-24, the RGB pins from the MICOM, and that helped make the message disappear while on RGB mode, but in non RGB mode part of it remains. Odd.

    So, refering to the schematic pics above (please note they are not from the unit but from a nearly identical unit. I could never find the service manual for my CRT but managed to find a unit using the same chassis and ICs, which helped immensely), I did the following:

    -Insert the RGB lines between the exiting resistor and the 75ohms resistor and grounding it (as was done on the video with the "mini triangles".

    -Jump RU10 680ohm resistor to cancel out the CCD

    -Contrary to the picture of the schematic of the jungle chip, the diodes shown were not available on my unit.

    -Found the 5V and GROUND on CN901 (Adjustment Port) and wired the 5V on ther third leg of the switch and the ground was left on standby for the time being (not used until testing the SMS)

    -Lifted the leg of the resistor (R919) closest to the MICOM and soldered a cable to the leg to the middle pin of the switch. Then I inserted another leg in the now available hole and soldered that to the remaining leg of the switch.

    -C919 and C916 are not found on my unit

    With this setup, the mod works as mentioned above, but the text kept appearing. So I desolered the leg closest to the MICOM chip for resistors R916-R918, breaking the pathway. This made the onscreen text disappear once and for all.

    Granted, by adjusting the flyback it made non RGB mode waaaaay to dark to even be considered playable, but RGB is just perfect and beautiful. Tehnically, it seems I'm pretty much done, but if I can make the OSD menu appear and disappear at will while on RGB mode, that would be fantastic and would put an end to this mod.

    Any ideas? Thanks everyone!
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	JUNGLE1.jpg 
Views:	4 
Size:	133.8 KB 
ID:	10836   Click image for larger version. 

Name:	MICOM1.png 
Views:	3 
Size:	123.2 KB 
ID:	10837  
    Proud owner of a Neo 25 Neo Geo Candy Cab!

Similar Threads

  1. Replies: 25
    Last Post: 02-08-2010, 10:19 PM
  2. What are the best card based video games (for any system)
    By backguard in forum Modern Gaming
    Replies: 23
    Last Post: 01-08-2008, 06:41 PM
  3. Does anybody remember books based on video games?
    By Gapporin in forum Classic Gaming
    Replies: 66
    Last Post: 06-24-2005, 05:39 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •